289680_1304714230_LUBRICATION.pdf | Motor Oil | Oils

Please download to get full document.

View again

of 32
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Information Report
Category:

Documents

Published:

Views: 5 | Pages: 32

Extension: PDF | Download: 0

Share
Related documents
Description
17–6 LUBRICATION – LUBRICATION SYSTEM (1AZ–FE) LUBRICATION SYSTEM (1AZ–FE) 1700F–09 ON–VEHICLE INSPECTION 1. CHECK ENGINE OIL LEVEL (a) After warm up the engine and then 5 minutes after the engine stop, oil level should be between the low level and full level marks of the dipstick. If low, check for leakage and add oil
Transcript
  1700F–09 A56466 Recommended Viscosity (SAE) BEFORE NEXT OIL CHANGETEMPERATURE RANGE ANTICiPATED4162738020406080100 –29 –20 –18–7  C  F20 W – 5015 W – 4010 W – 305 W – 30PREFERRED Oil Pressure Switch B11410   Oil Pressure SwitchOil Pressure Gauge B11411   Oil Pressure Gauge 17–6  –  LUBRICATION LUBRICATION SYSTEM(1AZ–FE)AVENSIS REPAIR MANUAL (RM1018E) LUBRICATION SYSTEM(1AZ–FE) ON–VEHICLE INSPECTION 1.CHECK ENGINE OIL LEVEL (a)After warm up the engine and then 5 minutes after the engine stop, oil level should be between thelow level and full level marks of the dipstick.If low, check for leakage and add oil up to the full level mark. NOTICE:Do not fill with engine oil above the full level mark.2.CHECK ENGINE OIL QUALITY (a)Check the oil for deterioration, entry of water, discoloringor thinning.If the quality is visibly poor, replace the oil. Oil grade: API grade ”SJ” Energy–Conserving, ”SL” Energy–Conserving or ILSAC multi grade engine oil. Recom-mended viscosity is as shown in the illustration.3.REMOVE OIL PRESSURE SWITCH ASSY (a)Disconnect the oil pressure switch connector.(b)Usinga deep socket wrench 24mm, remove the oil pres-sure switch. 4.INSTALL OIL PRESSURE GAUGE (a)Install the oil pressure gauge. 5.WARM UP ENGINE  Adhesive A50082  –  LUBRICATION LUBRICATION SYSTEM(1AZ–FE) 17–7 AVENSIS REPAIR MANUAL (RM1018E) 6.CHECK OIL PRESSUREOil pressure: At idle29 kPa (0.3 kgf/cm 2 , 4.3 psi) or moreAt 3,000 rpm245 to 539 kPa (2.5 to 5.5 kgf/cm 2 , 36 to 78 psi) or more 7.REMOVE OIL PRESSURE GAUGE8.INSTALL OIL PRESSURE SWITCH ASSY (a)Apply adhesive to 2 or 3 threads of the oil pressure switch. Adhesive:Part No. 08833–00080, THREE BOND 1344,LOCTITE 242 or equivalent (b)Using a deep socket wrench 24mm, install the oil pres-sure switch. Torque: 15 N  m (153 kgf  cm, 11 ft  lbf)NOTICE:Do not start the engine within 1 hour after the installation. (c)Connect the oil pressure switch connector. 9.START ENGINE AND CHECK FOR LEAKS  1700E–07 A56466 Recommended Viscosity (SAE) BEFORE NEXT OIL CHANGETEMPERATURE RANGE ANTICiPATED4162738020406080100 –29 –20 –18–7  C  F20 W – 5015 W – 4010 W – 305 W – 30PREFERRED B67536B67537 Oil Pressure Gauge  –  LUBRICATION LUBRICATION SYSTEM(1AZ–FSE) 17–13 AVENSIS REPAIR MANUAL (RM1018E) LUBRICATION SYSTEM(1AZ–FSE) ON–VEHICLE INSPECTION 1.CHECK ENGINE OIL LEVEL (a)After warm up the engine and then 5 minutes after the engine stop, oil level should be between thelow level and full level marks of the dipstick.If low, check for leakage and add oil up to the full level mark. NOTICE:Do not fill with engine oil above the full level mark.2.CHECK ENGINE OIL QUALITY (a)Check the oil for deterioration, entry of water, discoloringor thinning.If the quality is visibly poor, replace the oil. Oil grade: API grade ”SJ” Energy–Conserving, ”SL” Energy–Conserving or ILSAC multi grade engine oil. Recom-mended viscosity is as shown in the illustration.3.REMOVE OIL PRESSURE SWITCH ASSY (a)Disconnect the oil pressure switch connector.(b)Using a deep socket wrench 24mm, remove the oil pres-sure switch. 4.INSTALL OIL PRESSURE GAUGE (a)Install the oil pressure gauge. 5.WARM UP ENGINE  Adhesive A50082 17–14  –  LUBRICATION LUBRICATION SYSTEM(1AZ–FSE)AVENSIS REPAIR MANUAL (RM1018E) 6.CHECK OIL PRESSUREOil pressure: At idle29 kPa (0.3 kgf/cm 2 , 4.3 psi) or moreAt 3,000 rpm245 to 539 kPa (2.5 to 5.5 kgf/cm 2 , 36 to 78 psi) or more 7.REMOVE OIL PRESSURE GAUGE8.INSTALL OIL PRESSURE SWITCH ASSY (a)Apply adhesive to 2 or 3 threads of the oil pressure switch. Adhesive:Part No. 08833–00080, THREE BOND 1344,LOCTITE 242 or equivalent (b)Using a deep socket wrench 24mm, install the oil pres-sure switch. Torque: 15 N  m (153 kgf  cm, 11 ft  lbf)NOTICE:Do not start the engine within 1 hour after the installation. (c)Connect the oil pressure switch connector. 9.START ENGINE AND CHECK FOR LEAKS
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks