Fire alarm system EBL512 G3 - PDF

Please download to get full document.

View again

of 6
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Information Report
Category:

Computers & Electronics

Published:

Views: 4 | Pages: 6

Extension: PDF | Download: 0

Share
Related documents
Description
Fire alarm system EBL512 G3 An analog addressable fire alarm system for early detection - without any unwanted alarms. Generation three G3. Internet: pesn.panasonic.se Page 1 of 6 The demands
Transcript
Fire alarm system EBL512 G3 An analog addressable fire alarm system for early detection - without any unwanted alarms. Generation three G3. Internet: pesn.panasonic.se Page 1 of 6 The demands on fire alarm systems are increasing all the time. The most important task for a fire alarm system is an early detection of a fire in order to save life and property in different environments. Difficult detected fires, such as glowing / smouldering fires, have to be quickly and effectively detected. On the other hand, you also want to reduce the nuisance alarms to a minimum, i.e. the system has to have a high sensitivity and a low sensitivity at the same time . The system is also exposed to an increasing number of interferences such as mobile phones and other disturbances from the surroundings. All these demands require an intelligent system, i.e. both the control units and the detectors have to be intelligent. The system is EBL512 G3. General EBL512 G3 is an analog addressable Control and Indicating Equipment for fire alarm systems for buildings that fulfils the EN54 standards EN54 part 2 (C.i.e.) and EN54 part 4 (Power Supply). One control unit can, on four COM loops, handle up to 1020 input and/or output units, of which 512 can be alarm points such as detectors and manual call points. Each loop unit uses one address. Also conventional detectors can be connected to the system. Control and Indication Equipment EBL512 G3 with printer. EBL512 G3 can work as a single control unit or in a redundant TLON-network with up to 30 control units. The total number of loop units in a system is accordingly 30 x 1020 = ! Each control unit has access to all information from the other control units in the same network. EBL512 G3 - a unique concept for early and safe detection without any nuisance alarms EBL512 G3 is a user friendly fire alarm system with many unique functionalities and functions. Advanced alarm algorithms for contamination compensation, selfdiagnostics and inter activity makes the system suitable for almost any premises. Each analog detector in the system is individually supervised and the sensitivity of each analog smoke detector is constant - in spite of any contamination or background particles in the detection chamber. The long-term changes, such as contamination, are treated differently from the short-term changes, such as smoke from a smouldering fire. The self-diagnostic function detects every deviation from the accurate normal condition in the electronics and in the detection chamber. The inter activity function is using information from one, two or a larger number of detectors in the system, to provide a more secure detection of a real fire Page 2 of 6 A family of state of the art analog detectors gives the c.i.e. accurate information about the occurrence of smoke and/or temperature changes in the installation. The analog detector types 33xx (left) received a design award at the 1998 Hanover Exhibition. The newer analog detector types 43xx (right) have an even more attractive & slender design. A large variety of units can be connected to the four COM loops: Analog smoke & heat detectors Water proof heat detectors Addressable manual call points Addressable short circuit isolators Addressable I/O units (inputs / supervised voltage outputs as well as relay outputs) Addressable sirens / sounder bases Addressable beacons Intrinsically Safe (IS) detectors Wireless smoke detectors Conventional detectors (via I/O units or via expansion boards in the c.i.e.) The EL512 G3 fire alarm system has a set of functions that meets the most stringent requirements related to fire detection, fire presentation and measures to be taken. Automatic compensation for contamination, i.e. constant alarm sensitivity all the time. Service signal is given when a detector is contaminated to a certain level the service level. A large number of alarm algorithms is supported by the system and can be set for each analog detector individually Page 3 of 6 Alert Annunciation. The output for the alarm transmitter can be delayed for immediate on site investigation of a fire alarm. Individual detectors, zones, programmable outputs and outputs for the alarm transmitter can be individually disabled. Internally and/or externally controlled time channels. E.g. one or more alarm points may be disabled via a time channel. Outputs can be programmed in a very flexible way enabling control of sirens, fire doors, extinguishing systems etc. External Fire Brigade Panels and other Display Units can be connected to each c.i.e. Presentation of the actual system status in a PC via the Web-server II connected to an intranet (LAN) or Internet. Remote control with encrypted and safe two-way communication. In case of fire alarm, service signal etc. e- mails can be sent to the adequate personnel. Provides also one-way communication to an external computer system. Redundant TLON Network Up to 30 EBL512 G3 control units can be connected to a TLON Network. One of the units can be an external PC with a software driver for a Security Management system, which gives full control of and access to all data in all EBL512 G3 control units connected in the network. For full network redundancy, two parallel networks are used. All network programming is done with the Windows based PC software TLON Manager. Planning, commissioning and installation tool WinG3 EBL512 G3 is a very complex system. In order to get the optimal performance and cost effective planning, installation, commissioning and maintenance of a system, we provide our distributors with a powerful tool - the Windows based PC software WinG3, which is a complete support packet for the EBL512 G3 system. All configurations, control unit and system settings are done via WinG3. WinG3 is used when planning an installation. After the planning, the site specific data is downloaded to the control units. The data can also be uploaded. WinG3 is also used to download new software, etc. System overview Page 4 of 6 Products in the EBL512 G3 system Control and Indication Equipment (c.i.e.), etc EBL512 G3 C.i.e. With or without a printer and with 128, 256 or 512 alarm points depending on the article number (5000xxx). Supplied with a standard mounting plate approved for an incombustible wall, e.g. concrete EBL512 G3 C.i.e. A grey box , i.e. no front, no display & no door with Plexiglas. 128, 256 or 512 alarm points depending on the article number (5001xxx). Supplied with a standard mounting plate approved for an incombustible wall, e.g. concrete Mounting plate for a 19 mounting rack. (For one 5000 or 5001.) 5058 Mounting plate for an inflammable wall, e.g. wood. (For one 5000 or 5001.) 5013 Cabinet for drawings Expansion boards, etc conventional zones expansion board (8 zone line inputs) relays expansion board (8 relay outputs) 4583 In & outputs expansion board 5089 Connection cable with connectors for of up to six exp. boards Web-server II (SW: Web512 G3 II or OPC512 G3 II downloaded via a config. tool.) 1590 TLON connection board (One or two boards required per c.i.e.) Display Units, etc External Presentation Unit (EPU; Designation texts in Swedish / English) 1735 / 1736 Alert Annunciation Unit (AAU; Designation texts in Swedish / other language) 1826 / 1828 External Fire Brigade Panel (Ext. FBP; Metal / ABS plastic housing) Analog Detectors 3308 Analog heat detector * 3309 Analog heat detector, IP Analog base (For analog detectors) 3312F Analog base (For analog detectors) Fast connectors. 3312FL Analog base (For analog detectors) Fast connectors. Ext. LED output Analog multi detector * 4301 Analog photoelectric smoke detector * 4313 Analog base with isolator (For analog detectors) * Detector to be plugged in Analog base 3312 or Conventional Detectors (connected to a 3361 zone line input or exp. board 4580 zone line input) 2324 Base (For conventional detectors) 4318 Combination heat detector ** (59 degrees + rate-of-rise) 4350 Multi detector ** 4352 Photoelectric smoke detector ** 4375 Heat detector 60 degrees ** 4376 Heat detector 80 degrees ** 6295 Heat detector 60 degrees, IP Heat detector 80 degrees, IP Heat detector 100 degrees, IP Heat detector 120 degrees, IP67 ** Detector to be plugged in Base Intrinsically Safe equipment (analog / conventional) 2840 IS analog smoke detector (incl. back-box). For connection to IS analog heat detector (incl. back-box). For connection to IS barrier unit (for 2840 and 2841) 2814 IS manual call point (conventional, connected via 2820) 2820 Galvanic isolator (connected via 4580 input) xxxx Other peripheral devices 2218 External indicator (ext. LED) 3314 Address setting tool for the units connected to the COM loops 3333 Addressable manual call point 3339 Addressable manual call point, IP Addressable Multipurpose I/O unit (Two inputs & two outputs) 3364 Addressable 2 voltage outputs unit 3366 External power supply (Addressable) 3377 Addressable siren 3379 Addressable sounder base (for analog detectors 3308 and 430x) 4380 Addressable beacon 4582 I/O Matrix board (require also some kind of application board) 4610 Addressable Base station for wireless units 4601 Wireless smoke detector (incl. base) Page 5 of 6 MEW01267 (Rev 2) Jungmansgatan 12, SE Malmö, Sweden Tel: +46 (0) Fax: +46 (0) Internet: pesn.panasonic.se
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks