INTMOD485-LH Protocol Converter - PDF

Please download to get full document.

View again

of 7
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Information Report
Category:

Music

Published:

Views: 7 | Pages: 7

Extension: PDF | Download: 0

Share
Related documents
Description
For Use with L-GAGE LH Series Sensors Features Converts an LH Network to the 485-RTU protocol Supports baud rates up to 230,400 baud Supports LH Networks with up to 32 sensors Model Protocol Conversion
Transcript
For Use with L-GAGE LH Series Sensors Features Converts an LH Network to the 485-RTU protocol Supports baud rates up to 230,400 baud Supports LH Networks with up to 32 sensors Model Protocol Conversion Length INTMOD485-LH LH Network to 485-RTU 0.75 meter (2.46 ft) Overview The INTMOD485-LH protocol converter is used to convert an LH Network to the 485-RTU protocol. A PC or a PLC can communicate via to the converter on the front-end, and an LH Network of up to 32 sensors can communicate via the LH Network protocol on the back-end. The INTMOD485-LH will map the LH sensors digital output measurements to input registers. Both displacement and thickness delta measurements can be monitored, and the INTMOD485-LH protocol converter supports both polling and streaming sampling modes. INTMOD485-LH Adapter Cable PLC 18 to 30V dc CSB3-M1281M1282-LH Splitter LH Sensor Network NOTE: Banner recommends a maximum of 8 sensors per LH Network. The INTMOD485-LH does support an LH Network of up to 32 sensors; however, if your network requires more than 8 sensors, contact Banner for guidance on proper RS-485 wiring, termination, and/or using isolated RS-485 repeaters. WARNING: Not To Be Used for Personnel Protection Never use this product as a sensing device for personnel protection. Doing so could lead to serious injury or death. This product does NOT include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. P/N Rev. B 9/10/ Dimensions Specifications Input Power 18-30V dc from LH Network Operating Conditions Operating Temperature: 10º to +60 C (+14º to 140º F) Storage Temperature: -10º to +80º C (+14º to 176º F) Relative Humidity: 0 95% Non-condensing Vibration and Mechanical Shock Vibration: IEC , Hz, 0.5 mm P- P, 3 axis Shock: IEC , 30G, 11 milliseconds, half sine wave, 3 axis 485-RTU Connector 4-pin Euro-style QD connector LH Network Connector 8-pin Euro-style QD connector Current Less than 20 ma at the LH Network Environmental Rating IP67 Certifications Cable/Connector Wiring Table 1: 485-RTU (4-pin connector) Pin Color Pinout 1 Brown No Connect 2 White RS-485 / D1 / B / + 3 Blue RS-485 GND 4 Black RS-485 / D0 / A / tel: P/N Rev. B Table 2: LH Network (8-pin connector) Pin Color Pinout 1 White No Connect 2 Brown Power supply 18-30V dc 3 Shield No Connect 4 Yellow RS-485 RX-/TX- 5 Grey Ground of RS-485 bus 6 Green RS-485 RX+/TX+ 7 Blue Ground 8 Shield No Connect Configuration Data Table 3: Configuration Name Factory Value (register value in parentheses) Holding Register Address Modicon Holding Register Address Baudrate bps (1) Parity Even (0) LH Network Baudrate bps (1) Table 4: Configuration: Address Range Address (factory value = 1) Table 5: Configuration: Baudrate Value Baudrate 0xFFFF LH Network Same as LH Network Baudrate bps communicates at 9.6 Kb/s bps communicates at 19.2 Kb/s (factory value) bps communicates at 38.4 Kb/s bps communicates at 57.6 Kb/s bps communicates at Kb/s bps communicates at Kb/s Table 6: Configuration: Parity Value Type 0 Even Even parity bit is used (factory value) 1 Odd Odd parity bit is used 2 None No parity is used (stop bits MUST be set to 2) P/N Rev. B - tel: Table 7: Configuration: LH Network Baudrate Value Baudrate bps LH Network communicates at 57.6 Kb/s bps LH Network communicates at Kb/s (factory value) bps LH Network communicates at Kb/s Advanced Configuration Table 8: Advanced Configuration Name Factory Value (register value in parenthesis) Holding Register Address Modicon Holding Register Timeouts Extended (1) LH Network Size Auto (0xFFFF) LH Network Address Auto (0xFFFF) LH Network Sampling Mode Auto (0xFFFF) Table 9: Advanced Configuration: Timeouts Value Mode 0 Compliant Strict Timing 1 Extended Extended Timing (factory value) Table 10: Advanced Configuration: LH Network Size Value Size 0xFFFF Auto Dynamically discovers and adapts to LH Network size (factory value) 1-32 Fixed Fixed LH Network Size (1 to 32 sensors) Table 11: Advanced Configuration: LH Network Address Value Address 0xFFFF Auto Dynamically discovers first LH Network Address (factory value) 0-32 Fixed Fixed starting LH Network Address (address 0 to 32) Table 12: Advanced Configuration: LH Network Sampling Mode Value Mode 0xFFFF Auto Dynamically adapts to LH Network Sampling Mode (factory value) 0 Polling Measurement data will be polled on demand (LH Network Output Timer is disabled) 1 Streaming Measurement data will be streaming from LH Network (LH Network Output Timer is enabled) Measurements Table 13: Measurements LH Network Status LH Network Sampling Mode 4 - tel: P/N Rev. B LH Network Size LH Network Map [1-16] LH Network Map [17-32] LH Measurement [1] LH Measurement [2] LH Measurement [3] LH Measurement [4] LH Measurement [5] LH Measurement [6] LH Measurement [7] LH Measurement [8] LH Measurement [9] LH Measurement [10] LH Measurement [11] LH Measurement [12] LH Measurement [13] LH Measurement [14] LH Measurement [15] LH Measurement [16] LH Measurement [17] LH Measurement [18] LH Measurement [19] LH Measurement [20] LH Measurement [21] LH Measurement [22] LH Measurement [23] LH Measurement [24] LH Measurement [25] LH Measurement [26] LH Measurement [27] LH Measurement [28] LH Measurement [29] LH Measurement [30] LH Measurement [31] LH Measurement [32] P/N Rev. B - tel: Table 14: Measurements: LH Network Status Value Status 0 OK The LH Network is OK. The measurements are valid. 1 Unset Sensor An unset LH sensor is present on the LH Network. The measurement from the unset sensor is still valid. 2 LH Network Size Mismatch The expected LH Network Size and the actual LH Network Size do not match. The measurements are still valid. 3 LH Network Timeout The LH Network timed out. No sensors responded to the measurement request. The measurements are invalid. 4 LH Network Error The LH Network had a communication error during the measurement request. The measurements are invalid. Table 15: Measurements: LH Network Sampling Mode Value Mode 0 Polling Measurement data is being polled on demand (LH Network Output Timer is disabled) 1 Streaming Measurement data is streaming from LH Network (LH Network Output Timer is enabled) Table 16: Measurements: LH Network Size Value 0-32 Size of LH Network (number of discovered sensors) Table 17: Measurements: LH Network Map [1-16] Range 0x0000-0xFFFF 16-bit bitmap of sensors at addresses 1-16 on the LH Network. A sensor is mapped into the bitmap using its address as the index (i.e. bits 1-16 map to sensors at addresses 1-16). Table 18: Measurements: LH Network Map [17-32] Range 0x0000-0xFFFF 16-bit bitmap of sensors at addresses on the LH Network. A sensor is mapped into the bitmap using its address as the index (i.e. bits 1-16 map to sensors at addresses 17-32). Table 19: Measurements: LH Measurement [1-32] Value bit measurement value from LH sensor. LH Measurement[1] is from sensor at address 1, LH Measurement[2] is from sensor at address 2, etc. The LH sensor digital output is precisely calibrated over the range of Measurement readings outside of this range are considered invalid and should not be used. A value of 0 indicates that no measurement value was received for the sensor at the specified address. This will happen if the sensor is not present in the LH Network or there are communication timeouts/errors with the LH Network. NOTE: When using the INTMOD485-LH with an unset LH sensor (i.e. the sensor has not been assigned an address and is still at the factory default address of 0), the LH Network Status will be 1 (Unset Sensor), the LH Network Size will be 0, the LH Network Map will be 0x , and the unset LH sensor's measurement value will be available in the LH Measurement[1] register (input register 30006). Device Info Firmware Part Number 6 - tel: P/N Rev. B Firmware Version Firmware Build Model Part Number Model Version Config Part Number Config Version Datecode Accessories Cordsets Models Dimensions Pinout 4-Pin M12/Euro-Style Cordsets (straight connector) MQDC-406, 2 m (6.5') MQDC-415, 5 m (15') 42 Typ. [1.65 ] M12 x 1 MQDC-430, 9 m (30') ø 15 [0.59 ] Pin M12/Euro-Style Cordsets (right-angle connector) MQDC-406RA, 2 m (6.5') MQDC-415RA, 5 m (15') MQDC-430RA, 9 m (30') 32 Typ. [1.26 ] 30 Typ. [1.18 ] 1 = Brown 2 = White 3 = Blue 4 = Black M12 x 1 ø 14.5 [0.57 ] Banner Engineering Corp Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSE- QUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARIS- ING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp.
Recommended
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks