Removal of Phenol and Conventional Pollutants From Aqueous Effluent b

Please download to get full document.

View again

of 6
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Information Report



Views: 5 | Pages: 6

Extension: PDF | Download: 0

Related documents
Ingeniería ambiental
  Quim. Nova,  Vol. 32, No. 8, 2122-2127, 2009       A     r      t       i     g     o *e-mail: REMOVAL OF PHENOL AND CONVENTIONAL POLLUTANTS FROM AQUEOUS EFFLUENT BY CHITOSAN AND CHITINMaria Aparecida L. Milhome Departamento de Engenharia Hidráulica e Ambiental, Centro de Tecnologia, Universidade Federal do Ceará, Campus do Pici, 60451-970 Fortaleza – CE, Brasil Denis de Keukeleire Ghent University, Faculty of Pharmaceutical Sciences, Harelbekestraat 72, B-9000 Ghent, Belgium Jefferson P. Ribeiro e Ronaldo F. Nascimento* Departamento de Química Analítica e Físico-Química, Centro de Ciências, Universidade Federal do Ceará, Campus do Pici, 60451-970 Fortaleza – CE, Brasil Tecia Vieira Carvalho Parque de Desenvolvimento Tecnológico do Ceará, Universidade Federal do Ceará, Campus do Pici, Fortaleza – CE, Brasil Danilo Caldas Queiroz Departamento de Química Orgânica e Inorgânica, Universidade Federal do Ceará, Campus do Pici, Fortaleza – CE, BrasilRecebido em 7/1/09; aceito em 27/4/09; publicado na web em 7/10/09 The present study deals with phenol adsorption on chitin and chitosan and removal of contaminants from wastewater of a petroleum refinery. The adsorption kinetic data were best fitted to first- and second-order models for chitosan and chitin, respectively. The results of adsorption isotherms showed Langmuir model more appropriately described than a Freundlich model for both adsorbents. The adsorption capacity was 1.96 and 1.26 mg/g for chitin and chitosan, respectively. Maximum removal of phenol was about 70-80% (flow rate: 1.5 mL/min, bed height: 18.5 cm, and 30 mg/L of phenol. Wastewater treatment with chitin in a fixed-bed system showed reductions of about 52 and 92% for COD and oil and greases, and for chitosan 65 and 67%, respectively. The results show improvement of the effluent quality after treatment with chitin and chitosan.Keywords: adsorption; chitosan; phenol. INTRODUCTION One of the major problems of the petrochemical industry is the great amount of wastewater produced and the high investment needed for the treatment of this effluent before it is released in the environ-ment. In particular, phenol is present in significant concentrations, while it is highly toxic and accumulates in the environment. 1 Phenol can be removed from polluted water by chemical oxida-tion 2,3  or solvent extraction, 4,5  by using membranes 6,7  and by biological treatments. 8  However, these processes are not really efficient. An alternative is the use of adsorption methods and, in fact, this has been mostly applied for phenol removal and others organic compounds from polluted wastewaters. 9-11  A high efficiency is combined with recovery of solvents and removal of unwanted properties including color and odor. Activated carbon has been widely used for phenol removal, 12,13  but other adsorbents have been applied as well inclu-ding peat, bentonite, 14  amberlite resin, 15,16 biomass, 8  silica gel and activated alumina, 10  activated carbon zeolite, 17  coir pith carbon, 18  fly ash, 19  chitin 20 and chitosan. 21 Special attention has been paid to chitin, a natural polymer extracted from crab and shrimp shells, and chitosan, a derivative of chitin. These adsorbents have attracted much interest, because of their biodegradability, biocompatibility and hydrophilicity. Their use in the treatment of water and effluents has shown to be useful for removal of metals, 22-24  phenols, 25  dyes, 26  quinones 27  and others. 28-30  Chitin is obtained by treatment with dilute sodium hydroxide for deproteinization, followed by treatment with dilute hydrogen chloride for demineralization. Chitosan is produced by alkaline deacetylation of chitin. Alternatively, enzymatic treatment 31  has been developed to reduce the environmental impact and to reduce the cost of processing.The present study focused on phenol adsorption by chitin and chitosan using batch and column systems for possible use in the treat-ment of wastewater from petrochemical industries. The improvement of the quality of the effluent was evaluated by removal of phenol and the changes of physicochemical parameters such as pH, conductivity, chemical oxygen demand (COD), total oil and greases (TOG) and dissolved solids (DS). EXPERIMENTALMaterials The wastewater investigated was obtained from the petroleum refinery LUBNOR (Lubrificantes e Derivados de Petróleo do Nordeste, Fortaleza, CE, Brazil). Chitin (light white; ashes 0.30%; 60-200 mesh; molecular weight: 400,000 g/mol; pH 4.28) and chitosan (light yellow; 60-200 mesh; molecular weight: 174,205 g/mol, degree of deacetylation 90%, pH 7.93) were supplied by Delta - Natural and Dietary Products (Parnaíba, PI, Brazil). All reagents and solvents (Merck) were of analytical grade. A stock solution (1000 mg/L) of phenol was prepared and the standard solutions were obtained by diluting to the desired concentrations (10-50 mg/L). Chitosan and chitin were purified by soxhlet extraction and sonication as described by Rhee et al .. 32 Methods  Batch adsorption studies Water samples srcinating from a local petrochemical plant were  Removal of phenol and conventional pollutants from aqueous effluent2123 Vol. 32, No. 8 spiked with known amounts of phenol ranging from 10 to 50 mg/L and adsorption studies were carried out batchwise in order to obtain kinetic rates and equilibrium data. Closed flasks containing a known amount of adsorbent were agitated by shaking (150 rpm) for a period of 24 h at a particular pH and all experiments were conducted at room temperature (28±2 o C). pH changes during the course of the measurements were not observed.The effects of the dosage of adsorbent (2.5 x 10 -3  to 2.5 x 10 -2  g/ mL) and of pH (2 to 10) were studied. Kinetics and isotherms were determined using 0.2 g adsorbent and 20 mL phenol solution (10 to 50 mg/L) at equilibrium. After filtration (0.45 µ m membrane porosity), the residual phenol concentration was determined by HPLC. The adsorption capacity was obtained using Equation 1:   (1)where: q e  is the adsorption capacity (mg/g), C o  and C e  are the initial and equilibrium concentrations (mg/L), respectively, of phenol in solution, V is the volume (L), and W is the weight (g) of the adsorbent. Column adsorption studies A glass column (30 cm x 11 mm i.d.) filled with known mass of adsorbent corresponding to bed heights of 3.5, 8.5 and 18.5 cm, respectively, was percolated with 30 mL phenol solution (30 mg/L, at pH 6) at flow rates of 1.5, 3.0 and 6.0 mL/min, respectively. The characteristics of the bed are given in Table 1.Breakthrough curves of model and wastewater samples (spiked with 30 mg phenol/L) were determined in order to investigate the column capacity at complete exhaustion. The breakthrough curves were obtained by plotting C/C o  versus eluent volume. Aliquots of 10 mL were collected at the exit of the column for measuring the phenol concentration.Regeneration of the adsorbent was effected by using ethanol-water (1:1 v/v) as eluent (five times). For each cycle, 20 mL water was percolated first, followed by 10 mL effluent and 10 mL of eluent. The percentages of removal were calculated for each cycle.All column experiments were performed in duplicate at room temperature (28 ±  2 o C) and pH 6.0. Chromatographic analysis of phenol The phenol concentrations were determined by high-performance liquid chromatography (HPLC) using a Shimadzu SPD-10 A chro-matograph equipped with a LiChrospher 60 RP-select B column (12 cm, 5 mm i.d.) and an UV detector. The isocratic mobile phase was water-methanol 30:70 v/v, the flow-rate was 1 mL/min, and detec-tion was done at 270 nm. Before analysis, supernatant samples were filtered (0.45 µ m membrane porosity). Column adsorption in wastewater treatment  Treatment of the wastewater from a local petroleum refinery was carried out using a column filled with adsorbent (chitosan and chitin) for determination of various parameters including ‘Chemical Oxygen Demand’ (COD), ‘Total Oils and Greases’ (TOG), and ‘Dissolved Solids’ (DS) following procedures by ‘Standard Methods for the Examination of Water and Wastewater’. RESULTS AND DISCUSSIONBatch adsorption studies  Effect of adsorbent mass The effect of the dosage of adsorbent (2.5 x 10 -3  to 2.5 x 10 -2  g/mL) on phenol removal is shown in Figure 1. It can be observed that phenol adsorption increases in the range (5 x10 -3 -1 x 10 -2  g/mL) for both chitin and chitosan. According to this result, the adsorbent dosage was fixed at 1 x 10 -2  g/mL for all further experiments. Several factors influence the efficiency of phenol adsorption, such as changes pH and particle size (in this case: 60-200 mesh). Generally, smaller particles have greater capacity of analyte removal.  Effect of pH  The effect of pH on phenol adsorption by chitin and chitosan is represented in Figure 2. The data show that the phenol removal increa-sed with decreasing initial pH for both adsorbents. Chitin and chitosan contain functional groups such as hydroxy, acetamido, and amino that are prone to adsorb molecules by hydrogen bonds, Van der Waals inte-ractions, and ion exchanges. Depending on the pH, the amino groups are present in protonated or neutral forms. At low pH, the ammonium groups may exert electrostatic interaction with phenolates thereby increasing the adsorption efficiency. This behavior can be explained considering the fact that variations of pH affect the ionization of phenol (Equation 2a) and the surface properties of the adsorbent, denoted as Ads (Equations 2b, 2c).C 6 H 5 OH D  H + +   C 6 H 5 O -  (2a)Ads + H + D  Ads-H +  (2b)Ads-H +  +   C 6 H 5 O -   D  Ads-H +   - OC 6 H 5  (2c)As expected, adsorption decreases with increasing pH values (Fi-  Figure 1.  Effect of adsorbent dosage on removal of phenol by chitin and chi-tosan. Phenol concentration: 30 mg/L; pH 6; agitation time: 24 h; ambient temperature: 28 ±  2 o C  Table 1.  Properties of fixed-bed adsorbentPropertyChitosanChitinGranulometry (mesh)60-250 60-250 Diameter (D) (cm)1.101.10Bed height (L) (cm)18.518.5Adsorbent mass (g)1-3.901.2-3.36Apparent density (g/cm 3 )0.240.22Packed density ( ρ E ) (g/cm 3 )0.220.19Particles volume (V ap ) (cm 3 )16.2515.41Porosity ( ε )0.080.12  Milhome   et al. 2124 Quim. Nova gure 2), which may be attributed to the above factors. The phenolate fraction can be calculated from Equation 3: (3)where: C 0  is the initial phenol concentration, the pK a  of phenol is 9.9, and the pH is variable.Phenol is adsorbed to a lesser extent at higher pH values due to repulsive forces. Similar behavior has been reported by Halhouli et al . 33  for phenol adsorption by activated carbon and by Banat et al . 14  for phenol adsorption by bentonite. Similar results have also been obtained for phenol adsorption with chitosan, 34  chitin, 35  and bagasse fly ash. 19,36  It should be taken into account that, in this work, all ex-periments were conducted at pH 6 due to the solubility of chitosan at low pH, furthermore because of the pH of the wastewater investigated.  Adsorption kinetics In order to investigate the kinetics of phenol adsorption on chitin and chitosan, pseudo-first order, pseudo-second order, and intraparticle diffusion models were used. The adsorption kinetics were carried out for three initial phenol concentrations, 10, 30 and 50 mg/L, respectively, at adsorbent dosages of 1x10 -2  g/mL. The results, presented in Figures 3a and 3b, show that equilibrium was reached within 3, 5 and 6 h for chitosan, and within 3, 4 and 5 h for chitin.The experimental data were applied to the kinetic models for determi-nation of the rate constants (K 1  and K 2 ) using the equations of pseudo-first order (Equation 4) and pseudo-second order (Equation 5), respectively: (4) (5)where: q e  is the amount of phenol adsorbed at equilibrium, q is the adsorption capacity at time t, and K 1 and K 2  are rate constants of first order and second order, respectively. The rate constants K 1  and K 2  were calculated from log (q e -q) versus t and t/q versus t, respectively, for three initial concentrations. They are represented together with the correlation coefficients and adsorption capacities (Table 2). Based on results of experimental (q e ) and predicted (q t ) values, it can be noted that phenol adsorption on chitosan agrees well with first-order kinetics, indicating that the limiting stage of the adsorption process is a weak interaction with reversible character. However, results for chitin (Table 2) show that a pseudo-second-order model describes satisfactorily the adsorption of phenol, suggesting that the limiting stage of adsorption is a chemical interaction between phenol and adsorbent. Dursun et al. 35  also obser-ved that phenol adsorption onto chitin follows second-order kinetics.As is known, two intraparticle diffusion mechanisms are involved in the adsorption rate: diffusion within the pore volume (pore diffusion), diffusion along the surface of the pores (surface diffusion). Pore diffu-sion and surface diffusion occur in parallel within the adsorbent particle.  Adsorption isotherms The adsorption isotherms (relationship between adsorption ca-pacities and phenol concentrations at equilibrium) are given in Figure 4. The equilibrium adsorption data of phenol are well described by Langmuir (Equation 6) and Freundlich (Equation 7) models: (6)log q  = log K  F   + (1/  n ) log Ce (7)where: q is the amount adsorbed (mg/g), C e  is the equilibrium con-centration of phenol (mg/L), q max  and K L  are the Langmuir constants  Figure 2.  Effect of pH on phenol removal by chitin and chitosan. Adsorbent dosage: 1x10 -2 g/mL; phenol concentration: 30 mg /L; agitation time: 24 h; ambient temperature: 28 ±  2 o C   Figure 3.  Effect of agitation time and phenol concentration on adsorption of (a) chitosan and (b) chitin. pH: 6.0; adsorbent dosage: 1x10 -2 g/mL; ambient temperature: 28 ± 2 o C   Removal of phenol and conventional pollutants from aqueous effluent2125 Vol. 32, No. 8 related to maximum adsorption capacity (mg/g) and energy of ad-sorption, respectively, and K F  and n are Freundlich constants related to adsorption capacity and adsorption intensity, respectively. The Langmuir and Freundlich constants calculated from the linear plots of 1/  q e  versus 1/  C  e  and log q e  versus log C  e  together with the correlation coefficients ( r 2  ) are given in Table 3. The the-oretical data using Langmuir and Freundlich parameters from Table 3 are shown in Figure 4 to asses the validation of the model from the experimental data indicating that the adsorption equilibrium data for phenol followed the Langmuir and Freundlich isotherms for the adsorbents.However, a better criterion to test the correctness of the fits of the data is the normalized percent deviation, 37  which agrees with Equation 8: (8)where: q ex  is the experimental adsorption capacity, q pred  is the predicted adsorption capacity, and N is the number of observations. The lower the value of the percent deviation P is, the better the fit is (for values less than 5). The calculated P values (Table 3) suggest that the adsorption process for both adsorbents follows a Langmuir model occurring in monolayer surface. Maximum adsorption capacity (mg/g) was found to be 1.96 and 1.26 mg/g for chitin and chitosan, respectively. The favorable nature of adsorption can be expressed in terms of the separation factor R L, wich is defined in Equation 9:   (9)where: K L  is the Langmuir constant and C o  is the initial phenol concentration.The parameter R L  can be used to predict the affinity between the adsorbent and the adsorbate according to the criteria: not-favorable for R L  > 1, linear for R L  = 1 r, favorable for 0 < R L  < 1, and irreversible for R L  = 0. All values of R L  calculed for chitin and chitosan vary between 0 and 1 indicating that adsorption is favorable for both adsorbents.Table 4 provides the values of the adsorption capacities (mg/g) of adsorbents reported in other papers. It can be seen that activated carbon, fly ash, and chitin are efficient for removal of phenols. Also, chitin and chitosan have efficiencies comparable to other low-cost adsorbents like rice husk, cooke breeze, and grain rusk. New technologies to increase the adsorption capacity of chitosan have been developed through che-mical modification including substitution and cross-linking of chitosan chains. However, the cost of the material may be higher. Column adsorption studies  Effect of flow rate The results indicated that phenol removal decreased with increa-sed flow rates for both adsorbents, which is due to an increase of the hydraulical load (1.58-6.32 mL/min cm 2 ) in the column by an increase of the flow rate (1.5-6.0 mL/min). A flow rate of 1.5 mL/min has been adopted for further work. Large-scale applications of fixed-bed systems using chitin may cause problems due to clogging during the continuous flow of wastewater. Hence, it is necessary to optimize the system by adjusting the operational parameters. Moreover, a change of downflow to upflow may minimize clogging. Table 2.  Kinetic parameters of phenol adsorption by chitin and chitosanExperimentalPseudo -first-order kinetic modelPseudo- second-order kinetic modelDiffusion modelAdsorbentC o  (mg/L)q e  (mg/g)K 1 (h -1 )q t (mg/g) R 2 K 2 (g/mg.h)q t (mg/g) R 2 K i (mg/g.h -1/2  )R 2 Chitosan100.240.450.270.981.460.310.960.150.97301.490.201.470.950.052.760.930.660.93502.330.382.710.960.034.460.961.040.98Chitin100.400.310.250.942.740.430.991.680.94301.580.662.270.910.691.830.991.080.93502.700.604.610.950.323.  Figure 4.  Adsorption isotherms of chitosan and chitin. pH: 6.0; adsorbent dosage:1x10 -2 g/mL; ambient temperature: 28 ± 2 o C Table 3.  Parameters for Langmuir and Freundlich modelsLangmuirFreundlichAdsorbentq max (mg/g)K L R 2 P K F 1/nR 2 P Chitosan1.260.050.991.340.100.650.941.57Chitin1.960.030.964.520.140.490.984.96
View more...
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks